Accel AV316 Información técnica Pagina 45
- Pagina / 112
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
45
Table 15 — PIC 5 Alarm Codes (cont)
ALARM
CODE
(ALARMRST)
ALARM TEXT
DESCRIPTION
RESET TYPE
ACTION TAKEN BY
CONTROL
POSSIBLE CAUSE
INTEGRATED STARTER MODULE ALARMS (CONT)
Alm-413
ALM-413 ISM Fault —
Start Contact Fault
Manual Unit shuts down. Check 1M dry contact input.
Alm-414
ALM-414 ISM Fault —
Transition Contact Fault
Manual Unit shuts down. Check 2M dry contact input.
Alm-415
ALM-415 ISM Fault —
High Condenser Pressure
Manual Unit shuts down. Check high pressure switch.
Alm-416
ALM-416 ISM Fault —
Starter Fault
Manual Unit shuts down.
The ISM has received a start com-
mand and the starter has declared
a Fault. The dry contacts con-
nected to ISM J2-7 and J2-8 are
open. See starter display for starter
Fault Code.
For Benshaw Inc. RediStart start-
ers, view RediStart MICRO display.
For VFD, check VFD display Fault
History. Clear VFD faults with VFD
keypad.
For Allen-Bradley wye delta starters
with RLA > 718 A, the TR3 timer
may have expired as a result of a
delayed transition.
Alm-417
ALM-417 ISM Fault —
Motor Amps Not Sensed
Manual Unit shuts down.
The ISM has not sensed sufficient
current for an excessive delay after
1M has closed.
Check ISM_HIST screen
Check the MOTOR CURRENT CT
RATIO and the MOTOR RATED
LOAD AMPS in the ISM_CONF
screen.
Check VFD OPTION configuration.
Check for wiring of current trans-
formers to the J4 ISM terminals.
Check if main circuit breaker has
tripped.
Check ISM Status under the Main-
tenance Menu.
Alm-418
ALM-418 ISM Fault —
Excessive Acceleration
Time
Manual Unit shuts down.
Any line current remains high for an
excessive time duration following
1M aux and either 2M aux or transi-
tion contact closure.
Check that inlet guide vanes are
fully closed at start up.
Check ISM_HIST screen.
Check Motor Rated Load Amps in
ISM_CONF screen.
Reduce condenser pressure if pos-
sible.
Check ISM Status under the Main-
tenance Menu.
- AquaEdge 1
- Centrifugal Liquid Chillers 1
- AUX CONTROL PANEL 7
- STARTER PANEL 7
- LEGEND FOR FIG. 6-13 9
- Fig. 6 — IOB 1 10
- Fig. 7 — IOB 2 11
- Fig. 8 — IOB 3 12
- Fig. 9 — IOB 4 13
- Fig. 10 — Control Wiring 14
- Fig. 11 — HMI Panel 14
- Controls Outputs 16
- PIC 5 USER INTERFACE 16
- General Interface Features 17
- SETPOINT - Setpoint 18
- Unit Start / Stop 18
- Main Menu 19
- LOCAL Off 20
- PIC 5 CONTROL OPERATION 21
- Start-Stop Control — 21
- Chiller Start-Up Sequence 21
- Startup Sequence 21
- Control Points 22
- PRESSURE - Pressures 28
- CONF_PRG - Prognostics Config 29
- Trendings 30
- Table 16 — PIC 5 Alert Codes 47
- TOUCH SCREEN SETTINGS 52
- FOR THE CONTROLLER 52
- Welcome Screen Content — 53
- Intro screen 54
- COMMUNICATION PROBLEMS 55
- Hardware Problems — 55
- LEGEND 56
- 2— Proxy server 56
- Proxy Settings 57
- Main Menu Description 60
- GENERAL PARAMETERS 61
- Temperatures 62
- Input Status 63
- Output Status 64
- Hydraulic Status 64
- Run Times 65
- Setpoint Table 66
- Quick Test 66
- Configuration Menu 67
- Service Parameters 68
- Surge Correction Config 68
- Protective Limit Config 69
- Option Configuration 69
- ISM Configuration 70
- Factory Parameters 71
- General Configuration 71
- VFD Parameters 72
- SRD Configuration 72
- IOB Configuration 73
- E-Mail Configuration 73
- Master Slave Configuration 74
- Prognostics Config 74
- Reset Configuration 75
- User Configuration 75
- Schedule Menu 76
- Local Schedule 76
- Ice Build Schedule 76
- Network Schedule 77
- Holiday Menu 78
- Bacnet Config 79
- Maintenance Menu 80
- Capacity Control 81
- Override Control 82
- Surge Correction 83
- Maintenance ISM Config 83
- Swift Restart 84
- Master Slave 84
- Power Parameters 85
- ISM Status 86
- ISM History 86
- Maintenance SRD 87
- Maintenance Others 87
- Maintenance IOB 88
- Board Software PN 88
- Evap Pressure Sensor 91
- Cond Pressure Sensor 91
- Eco Pressure Sensor 91
- Diff Pressure Sensor 91
- Oil Sump Pressure 92
- Oil Supply Pressure 92
- Evap Entering Water P 92
- Evap Leaving Water P 92
- Cond Entering Water P 93
- Cond Leaving Water P 93
- Alarms Menu Description 94
- Alarm Reset 94
- DIP SWITCH SETTINGS 95
- DIP SWITCH SETTINGS (cont) 96
- HMI Dip Switch Settings — 96
- APPENDIX D — BACnet OPTION 98
- General — 98
- Table C — BACnet Point Table 100
- 107
- © Carrier Corporation 2014 112
Rowenta Vysavače uživatelské příručky
Začínající na C
Comentarios a estos manuales